Skip to main content

The XD-45 Compact

The XD-45 Compact
Springfield shrinks the grip frame to make the XD-45 more suitable for concealed carry.

Gun manufacturers are always striving to meet consumers' demands, and as more states adopt shall-issue concealed carry laws, law-abiding citizens are carrying guns for self-protection. This increases demand for suitable concealed carry firearms, and while some are satisfied with small-caliber, lightweight guns, others just are not comfortable without a substantial piece in the old reliable .45 ACP chambering. Certainly, there is no shortage of fine .45s on the market, but getting just the right one can be a challenge, especially if you are fond of a particular manufacturer's model and that model is too big to be the perfect solution.

The Springfield Armory XD-45 Compact is true to the XD line with grip safety, cocking indicator, ambidextrous magazine release and Ultra Safety Assurance trigger system. The gun comes with two magazines, one for 10 rounds and the other a 13 rounder with spacer to lengthen the grip to full size.

Five years ago Springfield Armory introduced its very popular XD line of pistols. Made in Croatia, they were available only in 9mm, .40 S&W and .357 SIG. In 2005 .45 GAP was added, and then in 2006 the XD-45 was unveiled in .45 ACP. It instantly became a hit in both the four-inch-barreled Service Model and the five-inch Tactical version. But unlike the other XDs that were available in full size and subcompact with a shortened barrel and grip, there was only one grip size for the XD-45. It was long enough to accommodate 13-round magazines, which was good, especially considering that the grip circumference was only slightly greater than the smaller-caliber versions, but it made the gun more difficult to conceal.

To remedy the situation, Springfield decided to shorten the grip length and lopped off about .7 inch from the four-inch-barreled Service Model. With a height of 4.9 inches, the XD-45 Compact still holds 10 rounds of .45 ACP cartridges but is easier to conceal under a shirt or jacket because the butt is less likely to create a tell-tale bulge.

Like all XDs, this Compact .45 has a polymer frame, which reduces weight considerably and adds to its desirability as a carry gun. There is also a grip safety that must be compressed to allow the trigger to function or the slide to open. Springfield's USA (Ultra Safety Assurance) trigger system employs a lever that prevents the trigger from moving unless the shooter's finger first depresses it in a deliberate attempt to fire the gun.

Using a variety of loads suitable for self-defense, the XD-45 Compact functioned perfectly with each trigger pull. Accuracy was good for a personal-defense carry gun, and despite the abbreviated grip, the gun was comfortable to shoot and easy to control.

Springfield Armory XD-45 Compact
MANUFACTURER: Springfield Armory
ACTION TYPE: Recoil operated
BARREL LENGTH: 4.04 inches
OVERALL LENGTH: 7.25 inches
WEIGHT: 29.25 ounces
CAPACITY: 10+1 small magazine,13+1 full-size magazine
GRIPS: Polymer
FINISH: Matte Blue
SIGHTS: Dovetail front and rear, three dot
PRICE: $588

A loaded-chamber indicator protrudes from the top of the slide and provides a visual and tactile warning that a round is chambered. When the striker is cocked, an indicator extends from the back of the slide and can be seen or felt to indicate the gun's readiness to fire.

The all-polymer grip is heavily checkered front and rear and is textured on both sides to offer a good non-slip surface. Although the XD-45 Compact's grip is comparatively short, it still affords ample area for a good solid hold. Some with larger hands might find their little finger hanging in mid-air below the bottom of the grip, but with my medium-size hands, my little finger still found a purchase, and even with hot +P .45 ACP defense loads the gun was pleasant to shoot. In fact, I think the circumference required to accommodate the double-stack design and the heavily textured surface would make the grip acceptable even to those with large hands.

The barrel is actually slightly over four inches long, but I'll call it four inches for practical purposes, and it is rifled with six lands and grooves. Overall length of the gun is 71?4 inches, and weight unloaded with the 10-round stainless steel magazine is 291?4 ounces. Height of the Compact is 4.9 inches with the 10-round magazine in place compared to 5.6 inches for the Service Model XD-45.

Springfield also supplies a regular 13-round stainless steel magazine with a sleeve that slides snuggly over it, making the Compact's grip equal in length to that of the Service Model XD-45. It's really a pretty good concept. With the 10-round magazine in place, the gun is more easily concealed, but with a spare 13-round magazine, there is plenty of backup firepower available.

The gun above in the foreground is the XD-45 Compact loaded with the 13-round magazine with grip extension. In the background is the standard full-size XD-45. Photo by Nyle Leatham

The Compact has a standard accessory rail for lights or lasers molded into the dustcover, and the slide is nicely finished in an attractive matte blue that goes well with the black polymer frame. If Springfield follows its normal pattern in the XD line, I expect it will soon offer the Compact with a stainless slide and frames in OD and Flat Dark Earth.

Compared to the XD-45 Service Model, the only difference is the length of the grip on the Compact, which has been shortened by about .7 inch to make it more easily concealable. Even with the shorter grip, the gun is comfortable to shoot.

XDs are recoil operated using the familiar modified Browning locked-breech design. The slide and barrel are locked together during the first fraction of an inch of recoil until the angled surface on the barrel lug contacts the locking block on the frame. This causes the barrel to cam downward and unlocks the breech, allowing the spent cartridge case to be extracted and ejected. The recoil spring then drives the slide forward, stripping a fresh cartridge from the magazine, and feeds it into the chamber. When the last shot is fired and the magazine is empty, the slide is held open by the external slide catch.

The full-size XD-45 Service Model magazine on the right holds 13 rounds of .45 ACP ammunition. The middle magazine is identical but has a spacer that slides over it to convert the Compact's grip to the same length as the Service Model. The 10-round Compact magazine is on the left. Photo by Nyle Leatham

The magazine release is ambidextrous and is easily operated with the thumb or trigger finger, allowing magazines to drop freely from the gun. Magazines are double stack and are therefore tapered at the top, making them easy to insert into the beveled magazine well. Speed reloads are a snap.

The XDs come standard with very functional, highly visible, drift-adjustable three-dot sights. Heinie or Trijicon tritium night sights are optional. Standard is a hard-sided, padded carrying case packed with XD gear consisting of a polymer holster, magazine pouch and magazine loader. A bore-cleaning brush and cable lock are also included.

That little wedge of steel on top of the slide is the loaded-chamber indicator that sticks up when a round is in the chamber. The USA trigger lever is a great safety device, as is the grip safety that prevents the trigger from being pulled unless it is depressed. The ambidextrous magazine release can be pushed from either the left or right side, and the grip safety must be depressed in order to pull the trigger or retract the slide.


Takedown and cleaning are very simple. As always, remove the magazine and double-check to make sure the gun is unloaded. Keeping the muzzle pointed in a safe direction, retract the slide and lock it to the rear by pressing the slide catch up into the slot on the slide. Remember that to retract the slide, the grip safety will have to be fully depressed.

When the slide is locked to the rear, rotate the takedown lever on the left side of the frame 90 degrees clockwise so it is straight up. Maintain a strong grip on the slide, and retract it slightly until the catch disengages, allowing the slide to move forward completely off the frame. The trigger will need to be pulled during this part of the operation in order to release the slide, so again, keep the muzzle pointed in a safe direction.

Factory Load Velocity (fps)SDAverage Group (ins.)
Black Hills 185-gr. JHP 948163.84
Hornady +P 230-gr. TAP FPD 85473.87
Hornady +P 200-gr. TAP FPD 987123.93
Cor-Bon +P 200-gr. JHP 1,080255.46
Velocity was recorded 10 feet from the muzzle with an Oehler 35P chronograph. Accuracy was tested off a Predator Shooting Rest. Results are the average of three five-shot groups at 25 yards. SD = Standard Deviation

Once the slide is free of the frame, turn it over and push the rear of the recoil-spring assembly slightly toward the muzzle to free it from the barrel lug. The spring assembly can then be lifted out as one unit. The barrel then is lifted from the slide, and all parts can be cleaned and lubricated. Assembly is in reverse order.

The XDs are duty and carry guns, not target pistols, so a very light, crisp trigger pull is just not a realistic expectation. The trigger on the XD is sort of a double-action-only design, except the trigger pull is not particularly long or heavy as one expects with a DAO revolver. The test gun had a short, light takeup followed by an 8.4-pound break as measured on my Lyman trigger-pull gauge. Specifications call for a trigger pull of 5.5 to 7.7 pounds, but the heavier pull on the test gun was not at all troublesome. However, I suspect that the trigger pull will become less after a short break-in period.

The cocked striker indicator protrudes from the back of the slide when the striker is cocked and warns the shooter both by sight and touch that the gun is ready to fire.


I tested the XD-45 Compact with four different loads, and the gun worked perfectly every single time the trigger was pulled. This is what I have come to expect of XDs. Recoil off the bench when testing for accuracy, or offhand when conducting tactical drills, was very controllable even with heavier-recoiling self-defense loads. In fact, I could not discern a difference compared to the Service Model XD-45 with full-length grip.

The Springfield Armory XD-45 Compact comes in a hard-sided, padded carrying case complete with both a short and long magazine, cleaning brush, cable lock, double magazine pouch, holster and magazine loader.

Using a Predator Shooting Rest at 25 yards, all loads proved to be plenty accurate for self-defense purposes. The best average of three five-shot groups was 3.84 inches with Black Hills 185-grain JHPs. Velocities and accuracy results are shown in the accompanying table.

After completing the accuracy test, I tried out the Compact on rapid-fire tactical drills and again found the Compact to deliver just like the four-inch-barreled Service Model XD-45 does. Recoil was easily managed, and the gun returned to target rapidly, delivering rounds to point of aim.

Springfield tells me the XD-45 Compact will be in dealer display cases by the time you read this. My guess is that the gun will prove to be a pretty popular choice.

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

See More Recommendations

Popular Videos

Performance Center M&P Shield M2.0

Performance Center M&P Shield M2.0

From Smith & Wesson, the M&P Shield M2.0 is a great option for a carry gun with optics option.

Ruger Security 9 Compact

Ruger Security 9 Compact

This handgun lives up to what Ruger wanted to build: a solid, dependable, easy-racking carry/home defense pistol at a better-than-reasonable price.

KelTec P17 22LR Pistol – Feature Packed, Accurate & Fun to Shoot

KelTec P17 22LR Pistol – Feature Packed, Accurate & Fun to Shoot

If you're in the market for a 17-round, compact .22LR pistol that's feature packed, then the P17 is definitely an option for you. At less than 14 ounces fully loaded, and barely longer than a dollar bill, the P17 is concealable for pretty much anyone. The threaded barrel, Picatinny-style accessory rail, ambidextrous safety, ambidextrous magazine release and three (3) 16rd magazines come standard. That's a lot of value added in such a small package.

Pistol Skills Drills - Hardball

Pistol Skills Drills - Hardball's Headache

The Hardball's Headache pistol drill is very similar to the El Presidente drill with a higher level of difficulty due to two added twists.

See More Popular Videos

Trending Articles

As you will learn in this detailed review, the Smith & Wesson M&P Shield EZ 380 (manufacturer SKU # 180023) is an easy-racking, soft-shooting pistol.Smith & Wesson M&P Shield EZ 380 Review Compact

Smith & Wesson M&P Shield EZ 380 Review

James Tarr - November 06, 2018

As you will learn in this detailed review, the Smith & Wesson M&P Shield EZ 380 (manufacturer...

Small, compact semi-auto pistols are popular with concealed-carry firearm buyers, and these two models – the KelTec PF9 9mm and the Ruger LCP II .22LR – are no exceptions. They are effective for personal protection but only if you put in the time to practice.Compact Carry Pistols Are Effective With Practice Training

Compact Carry Pistols Are Effective With Practice

Handguns Staff - August 14, 2020

Small, compact semi-auto pistols are popular with concealed-carry firearm buyers, and these...

The Smith & Wesson Model 13 revolver was a combat classic back in the day.Smith & Wesson Model 13 Revolver Revolvers

Smith & Wesson Model 13 Revolver

Payton Miller - July 31, 2020

The Smith & Wesson Model 13 revolver was a combat classic back in the day.

One of the newest in the Micro 9 series, the Kimber Micro 9 Nightfall is a serious pistol designed for personal defense.Kimber Micro 9 Nightfall Review Compact

Kimber Micro 9 Nightfall Review

Jeff Chudwin - January 29, 2019

One of the newest in the Micro 9 series, the Kimber Micro 9 Nightfall is a serious pistol...

See More Trending Articles

More Semi-Auto

The special edition 45th anniversary CZ 75 B is intended as a celebration of the manufacture and distribution of a pistol that has been embraced by civilian, military and law enforcement shooters around the globe.CZ 75 B 45th Anniversary Special Edition Pistol Semi-Auto

CZ 75 B 45th Anniversary Special Edition Pistol

Stan Trzoniec - May 14, 2020

The special edition 45th anniversary CZ 75 B is intended as a celebration of the manufacture...

The Springfield XD-M Elite 9mm pistol series upgrades the XD platform with four models and a number of significant new features.Springfield XD-M Elite Series – Four New 9mm Pistols for 2020 Semi-Auto

Springfield XD-M Elite Series – Four New 9mm Pistols for 2020

J. Scott Rupp - January 15, 2020

The Springfield XD-M Elite 9mm pistol series upgrades the XD platform with four models and a...

Kahr's K9 9mm pistol is a quarter-century old, and to commemorate the milestone the company is producing a limited-edition 25th anniversary K9.Kahr 25th Anniversary K9 Industry

Kahr 25th Anniversary K9

J. Scott Rupp - July 19, 2019

Kahr's K9 9mm pistol is a quarter-century old, and to commemorate the milestone the company is...

You don't have to spend a lot of money on a defense pistol to effectively protect your home and family.11 Best Defensive Pistols Under $500 Semi-Auto

11 Best Defensive Pistols Under $500

Brad Fitzpatrick - April 07, 2020

You don't have to spend a lot of money on a defense pistol to effectively protect your home...

See More Semi-Auto

Magazine Cover

GET THE MAGAZINE Subscribe & Save

Digital Now Included!


Give a Gift   |   Subscriber Services


GET THE NEWSLETTER Join the List and Never Miss a Thing.

Phone Icon

Get Digital Access.

All Handguns subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now